| PNC | Part code | Title | Quantity | Information |
i |
|---|
| 1 | | BRACKET, Brake & Clutch Pedal | | |
| 2 | | BOLT, Hex (7/16x14x4 1/2) | | |
| 3 | | NUT, Hex (5/16x18) | | |
| 4 | | WASHER, Lock (5/16) | | |
| 5 | | BRACKET, Pedal Bumper | | |
| 6 | | BRACKET, Clutch Swivel | | |
| 7 | | WASHER, Flat (1/4 ID x 1/2 OD) | | |
| 8 | | SCREW, Tap (1/4x14x3/4) | | |
| 9 | | SWITCH, Clutch Neutralizer | | |
| 10 | | BOLT, Hex (5/16x18x5/8) | | |
| 11 | | CLIP, Arm Asm | | |
| 12 | | SPACER, Clutch Pedal | | |
| 13 | | BUSHING, Pedal Shaft | | |
| 14 | | WASHER, Flat (15/32 ID x 7/8 OD) | | |
| 15 | | NUT, Hex (7/16x14) | | |
| 16 | | PLATE, Pad Trim | | |
| 17 | | COVER, Pedal Pad | | |
| 18 | | PEDAL ASM, Clutch | | |
| 19 | | BUMPER, Pedal | | |
| 20 | | CLIP, Clutch Arm Stop | | |
| 21 | | ROD, Pedal Push | | |
| 22 | | SEAL, Rod Release | | |
| 23 | | SEAT, Shaft Ball Stud | | |
| 24 | | STUD, Shaft Ball to Frame | | |
| 25 | | SPRING, Shaft Ball Stud Seat Ret | | |
| 26 | | SEAL, Shaft Ball Stud | | |
| 27 | | WASHER, Flat (25/64 ID x 1 OD) | | |
| 28 | | BRACKET, Lever & Shaft (1976-77 Shown) | | |
| 29 | | SCREW, Tap (5/16x12x7/8) | | |
| 30 | | WASHER, Lock (3/8) | | |
| 31 | | NUT, Hex (3/8x16) | | |
| 32 | | ROD, Fork Push (6 1/4 Long) | | |
| 33 | | SWIVEL, Push Rod | | |
| 34 | | BEARING, Clutch Release | | |
| 35 | | STUD, Ball Fork | | |
| 36 | | FORK, Clutch Release | | |
| 37 | | SPRING, Linkage Return | | |
| 38 | | BOOT, Release Fork | | |
| 39 | | NUT, Hex (3/8x16) | | |
| 40 | | RETAINER, Control Rods | | |
| 41 | | WASHER, Flat (25/64 ID x 3/4 OD) | | |
| 42 | | WASHER, Control Rods-Spring (13/32 ID x 49/64 OD) | | |
| 43 | | SEAL, Lever Shaft Ball Stud | | |
| 44 | | STUD, Lever Shaft Ball to Eng | | |
| 45 | | LEVER, W/Shaft, Clutch Control | | |
| 46 | | SCREW, Tap (#8-18x1/2) | | |
| 47 | | ROD, Clutch Fork Push | | |
